JRF5, 1/9 scale Grumman Goose
      Parts List
      12/7/95

      BALSA SHEETING:
      THK X WIDTH X LENGTH        QTY
      1/8  X 5 X 36                 6
      1/8  X 4 X 36                 3
      1/8  X 6 X 36                 2
      1/8  X 3 X 36                 6
      1/16 X 2 X 30                 2
      1/16 X 4 X 30                 2
      1/32 X 4 X 30                 1
      1/4  X 1 X 36                 2
      1/4  X 2 X 36                 2
      1/4  X 3 X 36                 2
      3/8  X 3 X 36   (1/2 USED)  1/2

      AIRCRAFT PLYWOOD
                   (AREA IN SQ INCHES)
      1/8  X L X W         480
      1/16 X L X W         198
      1/32 X L X W          97

      THE FOLLOWING IS ADDITIONAL REQD.
      (NOT INCLUDED IN ABOVE)
      WING: (FOR BOTH LEFT&RIGHT WINGS)
          MATERIAL               QTY  
       1/4 X 1/4 X 36 BALSA       2
       1/4 X 1/4 X 36 HARD WOOD   4
       (1/16 BALSA SHEETING WING SKIN 684*2=1368 SQ IN)
       (WING AREA=684 sq inch)
       1/16 X 4 X 36  BALSA      10 (WING SKINS)
      
       HORIZ STAB & ELEVATOR:
          MATERIAL                QTY   
       1/8  X 1/8 X 36 HARD WOOD   2 (ELEV)
       1/8  X 1/8 X 36 HARD WOOD   3 (HORIZ STAB)
       1/16 X 1/8 X 30 HARD WOOD   2 (ELEV)
      *1/32 X 130 SQ INCHES (PLY OR BALSA) HORIZ STAB
     **1/32 X 196 SQ INCHES (PLY OR BALSA) ELEV
        *NOTE: Skin/covering Stiff enough with balsa?
         *: I used 1/32 Bass Wood (flows well around contours)
        **: I used 1/16 Balsa Sheeting
            then covered with 3/4 OZ cloth
 
      FUES:
      3/32 X 4 X 36 BALSA          2 (FUES SIDES;BOAT SECTION)
      1/16 X 3 X 30 BALSA          2 (FUES TOP SECTION)
      1/16 X 3 X 30 BALSA          2 (ESTIMATED)(FOR AFT SECT
                                      AND FWD TOP SECT)
      1/2 X  1 X 8  BALSA          N1,N2:NOSE BLOCK,SEE DWG SHT 5
                    (CAN MAKE FROM 1/4" SCRAP SANDWICHED)
      1/6 X  4 X 30                4 (HULL FWD BOAT SECT©DOUBLE
                                      SKINNED)
      1/8 X  4 X 16                2 (HULL AFT BOAT SECT.)
      1/8 x  1/2 x 30 BALSA STRIP  2 (TOP FMRS F16,17,20&24)


      RUDDER:
      1/16 BALSA SHEETING FOR SKIN (45.13 SQ INCH X 2)

      NACELL:
      1/8  X 1/8 X 36 HARDWOOD            3 (TOTAL BOTH NACELLS)
      1/16 X 3 X 30   BALSA SHEETING      2 (TOTAL)

      STRINGERS(FUES,HSTAB,FLOATS,AFT SECTION)
      1/8 X 1/8 X 36 BALSA STRINGERS     20 (ESTIMATED)
      1/8 x 1/8 x 30 BALSA               14 (FUES TOP SECTIONS)
      1/8 X 1/8 X 36 BALSA  (BOAT SECT)  10 (ESTIMATED)

      1/4 X 1/2 X 36 BALSA                1 (FUES BOAT SECT)
      1/4 X 1/4 X 20 BALSA                2 (CORNER BOATSECT)
      1/4 X 1/4 X 16 BALSA                2 (CORNER BOATSECT)
      1/4 X 1/4 X 21 BALSA                1 (HSTAB LEADING EDGE)